Showing all 18 results
1.5A Motor Controller 2-way DC PWM Speed Dual H-Bridge
1.5A Mini Dual Channel DC Motor Driver Module PWM Speed Controller is a newly designed motor driver module for DIY robotics projects. This Mini Dual Channel DC Motor Driver Module PWM Speed Controller module is ideal for use in the battery-powered smart car, toy cars, robots. Supply voltage 2V ~ 10V can drive two DC motors or 4-wire 2-phase stepper motors, can achieve forward rotation or reverse rotation, it is possible to adjust the rotation speed.
30A ESC Brushless BLDC Motor Speed Controller
30A BLDC ESC Electronic Speed Controller is specifically made for quadcopters and multi-rotors and provides faster and better motor speed control giving better flight performance compared to other available ESCs. 30A BLDC ESC ELECTRONIC SPEED CONTROLLER can drive motors which consume up to 30A current. It works on 2S-3S LiPo batteries. It has an onboard BEC which provides regulated 5V(2A max draw) to power the flight controller and other onboard modules. It can be used to control our brushless motors with a 2S-3S LiPo (make sure motor doesn’t draw more than 30A). This particular ESC is recommended with A2212 brushless motor (1000kv, 1400kv, 2200kv).
DC 12V Motor 775 High RPM Torque With Bearing
DC 12V Motor 775 High RPM Torque With Bearing.Genuine product
Dual Shaft BO Motor-Straight 300 RPM
Dual shaft DC motor with gear box which gives good torque and rpm at lower voltages. This motor can run at approximately 200rpm when driven by a Dual Li-Ion cell battery at 6 V and approximately at 300 rpm when driven by a 9V Li-Ion cell.It is most suitable for light weight robot running on small voltage. Out of its two shafts one shaft can be connected to wheel, other can be connected to the position encoder.
Geared Motor DC , 12V, Center Shift 10- 500 RPM
DC Motor – 10 to 500 RPM – 12Volts geared motors are generally a simple DC motor with a gearbox attached to it. This can be used in all-terrain robots and variety of robotic applications. These motors have a 3 mm threaded drill hole in the middle of the shaft thus making it simple to connect it to the wheels or any other mechanical assembly.
10 to 500 RPM 12V DC geared motors widely use for robotics applications. Very easy to use and available in standard size. Also, you don’t have to spend a lot of money to control motors with an Arduino or compatible board. The most popular L298N H-bridge module with onboard voltage regulator motor driver can be used with this motor that has a voltage of between 5 and 35V DC or you can choose the most precise motor diver module from the wide range available in our Motor divers category as per your specific requirements.
Nut and threads on the shaft to easily connect and internally threaded shaft for easily connecting it to the wheel.DC Geared motors with robust metal gearbox for heavy-duty applications, available in the wide RPM range and ideally suited for robotics and industrial applications.Very easy to use and available in standard size. Nut and threads on the shaft to easily connect and internally threaded shaft for easily connecting it to the wheel.
L293D Motor Driver Shield for Arduino
This L293D Motor Driver Shield for Arduino is probably one of the most versatile on the market and features 2 servo and 4 motor connectors for DC or stepper motors. That makes it a great shield for any robotic project.
This Arduino compatible motor Driver shield is a full-featured product that it can be used to drive 4 DC motor or two 4-wire steppers and two 5v servos. It drives the DC motor and stepper with the L293D, and it drives the servo with Arduino pin9 and pin10.
L293D is a monolithic integrated, high voltage, high current, 4-channel driver. Basically, this means using this chip you can use DC motors and power supplies of up to 36 Volts, that some pretty big motors and the chip can supply a maximum current of 600mA per channel, the L293D chip is also what’s known as a type of H-Bridge. The H-Bridge is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.g. a motor.
The shield contains two L293D motor drivers and one 74HC595 shift register. The shift register expands 3 pins of the Arduino to 8 pins to control the direction of the motor drivers. The output enables the L293D is directly connected to PWM outputs of the Arduino.
Servo Tester PPM GENERATOR Module
A smart little servo tester than can be used to test servo motor, ESC and also to determine motor direction. Tests up to 3 servos at the same time.
The device also can be used as a signal generator for electric speed controller (ESC), for testing your motor system without using a transmitter and receiver.
4000W 220V SCR Voltage Regulator Adjust Speed Control Dimmer Thermostat
Adjustable Power Supply Board ,Connect this device with lamp or home appliance or electric circuit,then rotate the knob for dimming, speed, voltage, temperature control. It can use to such as electric stove, water heater tune thermal, lighting dimmer, small motor speed, electric iron thermostat, and achieve dimming, thermostats, pressure regulator effect.
8 mm Coin Flat Micro Vibrator Motor
Phone vibration motor is a DC brush motor for achieving the phone’s vibration feature, when you receive a text message or phone, the motor starts to drive high-speed rotating eccentric done, resulting in vibration. Specification： Type: 0834 Material: iron Size: 8*3.4mm，wire 15mm(L) Rated voltage : 3.0 VDC Rated current: 70mA Max Rated rotor speed: 12000±2500RPM Min Operating environment: -20℃～+60℃ Save environment::-30℃～+70℃ For: Mobile phones, Pager,Electronic vibration equipment Small size meets the needs of an increasingly mobile thin fuselage. Package includes: 1 PC Coin Flat Vibrating Micro Motor DC 3V 8mm For Pager and Cell Phone Mobile
A4988 driver 3D Printer Module Stepper Motor Driver + heat sink
The a4988 driver Stepper Motor Driver- Normal quality is a complete micro-stepping motor driver with built-in converter, easy to operate. The products can be in full, half, 1/4, 1/8 and 1/16 step mode of operation bipolar stepper motor, output drive performance up to 35 V and ± 2 A. a4988 driver Stepper Motor Driver includes a fixed off-time current regulator, the regulator can be in slow or mixed decay mode. The converter is the key to the easy implementation of the A4988. As long as the input of a pulse in the “step” in the input can be driven motor, micro-step
Rs.167.00Add to cart
AC 220V 2000W SCR Voltage Regulator Dimming Dimmers Speed Controller Thermostat
Connect this device with lamp or home appliance in a series connection, then rotate the knob for dimming, speed, voltage, temperature control.As the power has very big,so the normal home appliances or small factories enough to use.This pressure regulator with two-way high power silicon controlled, potentiometer have nuts, can use not need add any components, very convenient and practical.Connect this device with lamp or home appliance in a series connection, then rotate the knob for dimming, speed, voltage, temperature control.Applicable Appliance: Electric furnace, water heater, lamps, small motor, electric iron. etc
CoreLess Motors DC 3.7V-4.2V 50000RPM 7mm x 16mm Micro Brush Motor 2 Pcs Set
High speed core less samll motor . Its very use full for DIY project & your RC plane
DRV8825 Stepper Motor Driver Module for cnc 3d printer
The DRV8825 provides an integrated motor driver solution for printers, scanners, and other automated equipment applications. The device has two H-bridge drivers, and can drive a bipolar stepper motor or two DC motors. The output driver block for each consists of N-channel power MOSFET’s configured as full H-bridges to drive the motor windings. The DRV8825 can supply up to 2.5-A peak or 1.75-A RMS output current (with proper heatsinking at 24 V and 25°C).
A simple step/direction interface allows easy interfacing to controller circuits. Pins allow configuration of the motor in full-step up to 1/32-step modes. Decay mode is programmable. Internal shutdown functions are provided for overcurrent protection, short circuit protection, under-voltage lockout and overtemperature. The DRV8825 is available in a 28-pin HTSSOP package with PowerPAD (Eco-friendly: RoHS & no Sb/Br
L298N DC Motor Driver Controller 2A Stepper Motor Board Module
The L298N driver module, using ST’s L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential. Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability, low calorific value and strong anti-interference ability.
Rs.200.00Add to cart
PWM dc 6v 12v 24v 28v 3a motor speed controller
This DC Motor Speed Controller allows controlling the direction of a DC motor using a Pulse– Width-Modulated (PWM) DC voltage with a Duty Cycle fully adjustable from 0%-100%. The motor speed controller can easily provide a continuous current of3A to your DC motor or other DC load.
SG90 9g Mini Servo 1.2kgCm – 180 degree Rotation
The SG90 mini servo is lightweight, It is standard Quality and lightning-fast servo, designed to work with almost all the radio control systems. It is with excellent performance and high torque of 1.5kg cm gives you the freedom to use it for a variety of projects. The SG90 mini servo with accessories is perfect for R/C helicopter, plane, car, boat and truck use.
Rs.160.00Add to cart