Heat Shrink Tube assorted Size 1 Meter
74 in stock
Heat-shrink tubing (or, commonly, heat shrink or heatshrink) is a shrinkable plastic tube used to insulate wires, providing abrasion resistance and environmental protection for stranded and solid wire conductors, connections, joints and terminals in electrical work. It can also be used to repair the insulation on wires or to bundle them together, to protect wires or small parts from minor abrasion, and to create cable entry seals, offering environmental sealing protection. Heat-shrink tubing is ordinarily made of polyolefin, which shrinks radially (but not longitudinally) when heated, to between one-half and one-sixth of its diameter.
₹5.90 – ₹41.30 Price Including GST
CompareHeat Shrink Tube assorted Size 1 Meter
Material: Polyolefin Fully shrunk internal Shrinkage Ratio: 2 : 1(will maximum shrink to 1/2 of its supplied diameter) Minimum Shrinkage Temp: +70°C Full Shrinkage Temp: +120°C maximum Operating Temperature: -45°C to +125°C Tensile strength: 10.4 Mpa Dielectric strength: 15 kV/mm Flammability: Flame Retardant Cutting method: Scissors or sharp knife Manufacture specification: ISO9001 Approvals: UL Approved Package included: 1 Piece Black heat shrink sleeve 1.Flexible 2.Zero halogen 3.Flame retardant 4.Low smoke generation if burning 5.Continuous Operating Temperature:-45?to125? 6.Shrink Temperature:120
Based on 1 review
Add a review
You may also like…
-
Heat Shrink Sleeves
65mm PVC Heat Shrink Sleeve For Battery Pack 1M
One of the best ways to seal your battery is by using heat shrink. It can protect your battery from short circuits, seal your battery against the weather and add a professional look to your DIY battery.PVC heat shrink is great for battery use, but it can sometimes become brittle over time and begin to crack at the edges or at sharp corners. One method around this is to use multiple layers. This strengthens the heat shrink and adds a second line of defense if one layer should begin to crack. It also allows you to use multiple pieces of heat shrink perpendicular to each other to cover all six sides of a battery instead of just four sides, thus completely sealing your battery. Adding a thin layer of foam around your battery can also help prevent cracking of the heat shrink over time.
SKU: CE-BHST-65
Related products
-
Batteries & Chargers, Circuits Boards & PCB
5V 1A 2.1A Mobile Power Bank PCB 18650 Battery Charger Module with LCD
Batteries & Chargers, Circuits Boards & PCB5V 1A 2.1A Mobile Power Bank PCB 18650 Battery Charger Module with LCD
This is the mobile power module Accessories, 18650 Circuit board shell.
Meet the individual needs of your DIY, but you must understand basic electronic assembly.
Motherboard comes with protection function: Charging overcharge protection, over-discharge protection, overcurrent protection.
Intelligent output device after charging full, automatically stop charging, to prevent mobile phones overcharge.
Output voltage and current stable, will not harm user devices.SKU: CE-M010 -
Batteries & Chargers, Battery holder & Box, Circuits Boards & PCB
Battery Holder Cylindrical 3 AAA Plastic Battery Adapeter
Batteries & Chargers, Battery holder & Box, Circuits Boards & PCBBattery Holder Cylindrical 3 AAA Plastic Battery Adapeter
Battery Holder Black Cylindrical 3 AAA Plastic Battery Holder Adapter Case Box Flashlight Lamp. use as a replacement of 18650 battery model.
it comparable with all 18650 battery socketSKU: CE-E002-C-AAA -
Batteries & Chargers, Circuits Boards & PCB, Power Supply
LM 2596 DC Buck Converter Module
This is an LM2596 DC-DC buck converter step-down power module with high-precision potentiometer for adjusting output voltage, capable of driving a load up to 3A with high efficiency. When the output current required is greater than 2.5A(10W) an external heatsink is suggested. Use on board switch to change display measurement between the input or output voltage, and a LED indicate which value(IN/OUT) is being measured. This setting is stored even after power off. Voltmeter can be turned off, just keep the switch pressed for 1 second and leave it. Adjust Input and output voltage measurement error offset – long press switch for 4 seconds or more, the digital display flashes, then short press the button to change the value of output (values range from -0.5 to 0.5, the unit is V), a positive number indicates an upward calibration, negative downward calibration. Now press the button again for adjust input offset in same manner.
SKU: CE-M064 -
Batteries & Chargers, Battery holder & Box, Circuits Boards & PCB, Power Supply
Lithium Battery Charging Board TP 4056 Micro USB with Protection
Batteries & Chargers, Battery holder & Box, Circuits Boards & PCB, Power SupplyLithium Battery Charging Board TP 4056 Micro USB with Protection
This tiny module is perfect for charging single cell 3.7V 1 Ah or higher LiPo cells such as 16550s that don’t have their own protection circuit.Based around the TP4056 charger IC and DW01 battery protection IC this module will offer 1A charge current then cut off when finished.Futhermore when the battery voltage drops below 2.4V the protection IC will switch the load off to protect the cell from running at too low of a voltage – and also protects against over-voltage and reverse polarity connection (it will usually destroy itself instead of the battery) however please check you have it connected correctly the first time.
For Bulk Quantity Please call US:- +91 9830150448
SKU: CE-M029
Suman Dey (verified owner) –
Nice product
Suman Dey –