Alcohol Sensor MQ3 Module for all MCU
Out of stock
This is a simple to use MQ-3 Alcohol Detector Gas Sensor Module which can sense the presence of Alcohol in the air. The module uses our MQ-3 sensor. It simplifies the interface to the odd pin spacing of the sensor and provides an interface through standard 4 x 0.1″ header pins. It provides an analog output corresponding to the concentration of the gas in the air and an easy to use digital output. The onboard potentiometer can be used to set the maximum gas concentration beyond which the digital output gets triggered. Just power the module with 5V set the threshold and you can start getting the gas concentration of the air around the sensor! An onboard LED signals the presence of any gas. Perfect sensing alcohol concentration on your breath just likes common breathalyzer.
₹141.60 Price Including GST
Out of stock
CompareAlcohol Sensor MQ3 Module for Arduino & other
QUICK GUIDE
- Sensitive to alcohol, ethanol
- Fast response and recovery
- Adjustable sensitivity
- Signal output indicator
- Analog and level signal output.
- The carbon monoxide detection with better sensitivity.
- Has a long service life and reliable stability.
- Rapid response recovery features.
- Output voltage boosts along with the concentration of the measured gases increases
- TTL output valid signal is low. (When the output low signal light can be directly connected microcontroller or relay module).
Specifications and Features:
- Model No.: MQ-3
- Dimensions: 36 x 20 x 21 mm (LxWxH)
- Weight: 6gm
- Heater voltage: 5±0.2V (AC•DC)
- Loop voltage: ≤24V (DC)
- Load resistance: adjustable
- Heating Resistance: 31Ω±3Ω (Room temperature)
- Heating Power: ≤ 900mW
- Surface thermal resistance: 2Kohm-20Kohm (0.4mg/L alcohol)
- Sensitivity: Rs (in air)/Rs (0.4mg/L alcohol) ≥ 5
- Working temperature: 20 degrees ±2 degree
- Humidity: 65%±5%RH
- Signal output light indicator.
- Analog and level signal output.
- TTL output valid signal is low. (When the output low signal light can be directly connected microcontroller or relay module).
- The carbon monoxide detection with better sensitivity.
- Has a long service life and reliable stability.
- Rapid response recovery features.
Datasheet MQ-3 datasheet
Based on 0 reviews
Be the first to review “Alcohol Sensor MQ3 Module for all MCU”
Related products
-
Developments Boards, Modules & Sensors
HUMIDITY DETECTION SENSOR MODULE HR202 LM393
HR202 is a new kind of humidity-sensitive resistor made from organic macromolecule materials, it can be used in occasions like: hospitals, storage, workshop, textile industry, tobaccos, pharmaceutical field, meteorology, etc.
SKU: CE-M008 -
Developments Boards, Modules & Sensors
USB ASP ISP Programmer for 8051
USBasp is a USB in-circuit programmer for Atmel AVR controllers. It simply consists of an ATMega8 and a couple of passive components. The programmer uses a firmware-only USB driver, no special USB controller is needed, and thats make it low cost USB programmer.
The Programmer works on USB port and can be used with Laptops. Software is compatible with Windows Vista and Windows 7. High speed programming and does’t require external power.
SKU: CE-P002 -
Circuits Boards & PCB, Developments Boards, Modules & Sensors
Joystick Module Dual Axis XY for arduino & other
Circuits Boards & PCB, Developments Boards, Modules & SensorsJoystick Module Dual Axis XY for arduino & other
This is a dual axis high quality JoyStick Module . It can be used to sense movements in 2 directions(axes). It also has a inbuilt switch which can be activated by pressing the stick.Directional movements are simply two potentiometers – one for each axis. Pots are ~10k each.
With the help of this Joystick Module, you can measure position coordinates on the X and Y axis by moving the “hat”. It also contains a switch that is press-able by pushing the “hat”.It also contains a switch that is press-able by pushing the “hat” down. Similar to the XBOX controller.The X and Y axes are two 10k potentiometers which control 2D movement by generating analog signals. When the module is in working mode, it will output two analog values, representing two directions. This module uses the 5V power supply, and value, when reading through analog input, would be about 2.5V, a value will increase with joystick movement and will go up till maximum 5V; the value will decrease when the joystick is moved in other direction till 0V.
SKU: CE-M096 -
Developments Boards, Modules & Sensors
MAX6675 Thermocouple Temperature Sensor Module For Arduino
The MAX6675 performs cold-junction compensation and digitizes the signal from a type-K thermocouple. The data is output in a 12-bit resolution, SPI™-compatible, read-only format. This converter resolves temperatures to 0.25°C, allows readings as high as +1024°C, and exhibits thermocouple accuracy of 8LSBs for temperatures ranging from 0°C to +700°C. The MAX6675 is available in a small, 8-pin SO package
SKU: CE-M047
There are no reviews yet.