2S 3A Li-ion Lithium Battery Charger 7.4v 8.4V Protection Board
Out of stock
2S 3A Li-ion Lithium Battery 7.4V 8.4V 18650 Charger Protection Board Module is a small PCB mounted Li-ion Lithium Battery charger protection module. This small and smart battery charger protection module comes with the various features like Short circuit protection, Overcharge protection, Over-discharge protection, Overcurrent protection. It is very easy to install and convenient to use in all your DIY portable projects.
₹88.50 Price Including GST
Out of stock
Compare2S 3A Li-ion Lithium Battery Charger 7.4v 8.4V Protection Board features
-
-
- Protections:
- Short circuit protection
- Overcharge protection
- Over-discharge protection
- Overcurrent protection
- Overcharge Detection Voltage: 4.25-4.35V±0.05V
- Over Discharge Detection Voltage: 2.3-3.0V±0.05V
- Maximum Working Current: 3A
- Transient Current: 5A
- Operating Temperature: -40-50 C
- Internal Resistance: Less than 45m Ω
- B+ B-: The interface of battery core
- P+ P-: The connector of battery board
- MB: The connection point between the batteries
- B+: Battery V+ Positive
- B-: Battery V- Negative
-
- P+: Output / Charging V+
- P-: Output / Charging V-
- Size: Approx. 36x6x1mm/ 1.42″ x 0.24″ x 0.04″
NB: Please make sure when connection your batteries.
Based on 0 reviews
Be the first to review “2S 3A Li-ion Lithium Battery Charger 7.4v 8.4V Protection Board”
Related products
-
Batteries & Chargers, Circuits Boards & PCB
Lipo Battery Low Voltage Tester 1S-8S Buzzer
The LiPo low voltage Tester cum Alarm is small and light for on board use, plugs into balance lead for detecting low voltage on individual cells. A loud alarm will go off with flashing LED if the voltage on any of the individual cells drops below the adjustable threshold. Essential while working with any Lithium Polymer battery.
SKU: CE-M071 -
Batteries & Chargers, Circuits Boards & PCB, Power Supply
18650 Battery Charger module 5V 1A Module for PowerBank
Batteries & Chargers, Circuits Boards & PCB, Power Supply18650 Battery Charger module 5V 1A Module for PowerBank
It is 18650 Mobile power bank Battery Charge, Discharge, Protection & Boost Circuit board module.You can make your own power bank using this module. It can charge up to 4 batteries in parallel.Can show the battery charge & discharge status with two mode on-board LED’.(Blink& Standby)Module comes with protection function, Overcharge protection, Over-discharge protection, Over current protection.Intelligent Overcharge protection system automatically stops charging once the connected device is fully charged. Stable Output voltage and current.
SKU: CE-M073 -
Batteries & Chargers, Circuits Boards & PCB, Power Supply
LM 2596 DC Buck Converter Module
This is an LM2596 DC-DC buck converter step-down power module with high-precision potentiometer for adjusting output voltage, capable of driving a load up to 3A with high efficiency. When the output current required is greater than 2.5A(10W) an external heatsink is suggested. Use on board switch to change display measurement between the input or output voltage, and a LED indicate which value(IN/OUT) is being measured. This setting is stored even after power off. Voltmeter can be turned off, just keep the switch pressed for 1 second and leave it. Adjust Input and output voltage measurement error offset – long press switch for 4 seconds or more, the digital display flashes, then short press the button to change the value of output (values range from -0.5 to 0.5, the unit is V), a positive number indicates an upward calibration, negative downward calibration. Now press the button again for adjust input offset in same manner.
SKU: CE-M064
There are no reviews yet.