18650 Battery Charger module 5V 1A Module for PowerBank
87 in stock
It is 18650 Mobile power bank Battery Charge, Discharge, Protection & Boost Circuit board module.You can make your own power bank using this module. It can charge up to 4 batteries in parallel.Can show the battery charge & discharge status with two mode on-board LED’.(Blink& Standby)Module comes with protection function, Overcharge protection, Over-discharge protection, Over current protection.Intelligent Overcharge protection system automatically stops charging once the connected device is fully charged. Stable Output voltage and current.
₹116.82 Price Including GST
87 in stock
Compare18650 Battery Charger module 5V 1A Module for PowerBank
Input Micro USB: 5V 1A
USB Output: 5V 1A
Batteries Type: Lithium-ion batteries (18650)
Battery Quantity: Can operate up-to 3 batteries in parallel
Installation instructions:
First connect all your batteries (maximum 3 nos.) in parallel to make a battery pack.
Then connect a thick copper wire from -ve of battery pack to B-
Now connect a thick copper wire from +ve of battery pack to B+
*** DO NOT CONNECT IN REVERSE POLARITY ***
Connecting the batteries in reverse will burn the board.
Put an insulation between the battery pack & this module to avoid any short circuit
Based on 0 reviews
Be the first to review “18650 Battery Charger module 5V 1A Module for PowerBank”
You may also like…
-
Batteries & Chargers, Circuits Boards & PCB
5V 1A 2.1A Mobile Power Bank PCB 18650 Battery Charger Module with LCD
Batteries & Chargers, Circuits Boards & PCB5V 1A 2.1A Mobile Power Bank PCB 18650 Battery Charger Module with LCD
This is the mobile power module Accessories, 18650 Circuit board shell.
Meet the individual needs of your DIY, but you must understand basic electronic assembly.
Motherboard comes with protection function: Charging overcharge protection, over-discharge protection, overcurrent protection.
Intelligent output device after charging full, automatically stop charging, to prevent mobile phones overcharge.
Output voltage and current stable, will not harm user devices.SKU: CE-M010 -
Batteries & Chargers, Battery holder & Box, Circuits Boards & PCB, Power Supply
Lithium Battery Charging Board TP 4056 Micro USB with Protection
Batteries & Chargers, Battery holder & Box, Circuits Boards & PCB, Power SupplyLithium Battery Charging Board TP 4056 Micro USB with Protection
This tiny module is perfect for charging single cell 3.7V 1 Ah or higher LiPo cells such as 16550s that don’t have their own protection circuit.Based around the TP4056 charger IC and DW01 battery protection IC this module will offer 1A charge current then cut off when finished.Futhermore when the battery voltage drops below 2.4V the protection IC will switch the load off to protect the cell from running at too low of a voltage – and also protects against over-voltage and reverse polarity connection (it will usually destroy itself instead of the battery) however please check you have it connected correctly the first time.
For Bulk Quantity Please call US:- +91 9830150448
SKU: CE-M029
Related products
-
Batteries & Chargers, Circuits Boards & PCB, Modules & Sensors
0.36 Inch DC 0-100V LED Mini Digital Voltmeter Blue/red/green Volt Meter 3 wires
Batteries & Chargers, Circuits Boards & PCB, Modules & Sensors0.36 Inch DC 0-100V LED Mini Digital Voltmeter Blue/red/green Volt Meter 3 wires
- this voltmeter uses three-position 0.36inch LED digital tube display, no shell, thin thickness, small appearance, low price, stable performance and good display.
- The measuring range of the voltmeter can be DC 0-100V. The working power supply should be supplied by the outside, the voltage range is DC 4.5-30V, and the protection will be received.
- The display resolution of this voltmeter is fixed to 0.1V.
- This voltmeter is suitable for users with DC power supply to save cost. Or you need to start measuring from 0V
SKU: n/a -
Batteries & Chargers, Circuits Boards & PCB, Power Supply
LM 2596 DC Buck Converter Module
This is an LM2596 DC-DC buck converter step-down power module with high-precision potentiometer for adjusting output voltage, capable of driving a load up to 3A with high efficiency. When the output current required is greater than 2.5A(10W) an external heatsink is suggested. Use on board switch to change display measurement between the input or output voltage, and a LED indicate which value(IN/OUT) is being measured. This setting is stored even after power off. Voltmeter can be turned off, just keep the switch pressed for 1 second and leave it. Adjust Input and output voltage measurement error offset – long press switch for 4 seconds or more, the digital display flashes, then short press the button to change the value of output (values range from -0.5 to 0.5, the unit is V), a positive number indicates an upward calibration, negative downward calibration. Now press the button again for adjust input offset in same manner.
SKU: CE-M064
There are no reviews yet.