8 Channel Relay Module 5V with Optocoupler
6 in stock
It is an 8 Channel Isolated 5V 10A Relay Module, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc. It is also able to control various appliances and other types of equipment with large current. Relay output maximum contact is AC250V 10A and DC 5V 10A. One can connect a microcontroller with standard interface directly to it. Red working status indicator lights are conducive to the safe use. It has a wide range of applications such as all MCU control, industrial sector, PLC control, smart home control.
₹295.00 Price Including GST
6 in stock
Compare8 Channel Relay Module 5V with Optocoupler
Can be used as microcontroller development board module can be used as home appliance control
5 V-12V to TTL control signal
The control signal DC or AC, 220V AC load can be controlled.
There is a normally open and one normally closed contact
A power indicator light
A control indicator, pull off, disconnect does not shine
Transistor drive to increase the relay coil control pins high impedance.
The control pin has a pull-down circuit to prevent malfunction relay vacantly
Specifications:-
- Maximum load: AC 250V/10A, DC 30V/10A
- Trigger current: 5mA
- Working voltage: 5V
- Module size: 50 x 26 x 18.5mm (L x W x H)
- Four mounting bolts holes, diameter 3.1mm
- DC+: positive power supply (VCC)
- DC-: negative power supply (GND)
- IN: can be high or low level control relay
- NO: normally open relay interface
- COM: Common Interface Relays
- NC: normally closed relay interface
- It is low level trigger when jumper connect to LOW pin
- It is high level trigger when jumper connect to HIGH pin
Based on 0 reviews
Be the first to review “8 Channel Relay Module 5V with Optocoupler”
You may also like…
-
Circuits Boards & PCB, Developments Boards, Modules & Sensors, Robots & Kits
2-Channel 5V Relay Module With optocoupler For arduino & other
Circuits Boards & PCB, Developments Boards, Modules & Sensors, Robots & Kits2-Channel 5V Relay Module With optocoupler For arduino & other
This is a 2 Channel 5V Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Microcontroller(Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) .
SKU: CE-M051 -
Developments Boards, Modules & Sensors
4 Channel Relay Module 5V with optocoupler
This is a 5V 4-channel relay interface board, and each channel needs a 15-20mA driver current. It can be used to control various appliances and equipment with large current. It is equiped with high-current relays that work under AC250V 10A or DC30V 10A. It has a standard interface that can be controlled directly by microcontroller.
SKU: CE-M0118 -
Modules & Sensors
Single Channel relay module 5V with Optocoupler
Single Channel relay module 5V with Optocoupler. This 1 channel 5V 10A relay control board module with optocoupler modules is compliant with international safety standards, control and load areas isolation trenches it has a single relay a genuine.
SKU: CE-M051-1 -
IoT & Wireless, Modules & Sensors
Relay Module ESP-01 5V WiFi 5V For Remote Control Switch
This WiFi relay module carries a ESP8266 WiFi module and micro controller. It will send the serial port instructions to the cell phone APP and Implementation within the local area network (LAN) for wireless control relay.
SKU: CE-M0119
Related products
-
IoT & Wireless, Modules & Sensors
NEO6MV2 GPS Module NEO-6M with Flight Control EEPROM
This is a complete GPS module that is based on the Ublox NEO-6M. This unit uses the latest technology from Ublox to give the best possible positioning information and includes a larger built-in 25 x 25mm active GPS antenna with a UART TTL socket. A battery is also included so that you can obtain a GPS lock faster. This is an updated GPS module that can be used with ardupilot mega v2. This GPS module gives the best possible position information, allowing for better performance with your Ardupilot or other Multirotor control platform.
The Ublox NEO-6M GPS engine on this board is a quite good one, with the high precision binary output. It has also high sensitivity for indoor applications. UBLOX NEO-6M GPS Module has a battery for power backup and EEPROM for storing configuration settings. The antenna is connected to the module through a ufl cable which allows for flexibility in mounting the GPS such that the antenna will always see the sky for best performance. This makes it powerful to use with cars and other mobile applications.
The Ublox GPS module has serial TTL output, it has four pins: TX, RX, VCC, and GND. You can download the u-center software for configuring the GPS and changing the settings and much more.
SKU: CE-M0110 -
IoT & Wireless
RA-02 LoRa Module Breakout Board, RF Wireless Transceiver
Ra-02 is a wireless transmission module based on SEMTECH’s SX1278 wireless transceiver. It adopts advanced LoRa spread spectrum technology, with a communication distance of 10,000 meters. It has strong ability of anti-jamming and has the function of air wake-up Consumption. Can be covering thousands of people in the district environment, particularly suitable for meter reading, smart home, burglar alarm equipment. The LoRa series module Ra-02 is designed and developed by AI-THINKER Technology. The SX1278 RF module is mainly used for long-range spread spectrum communication. It can resist Minimize current consumption. Thanks to SEMTECH’s patented LoRa ™ modulation technology, the SX1278 has a high sensitivity of -148 dBm with a power output of +20 dBm, a long transmission distance and high reliability. At the same time, compared with the traditional modulation technology, LoRa ™ modulation technology has obvious advantages in anti-blocking and selection, which solves the problem that the traditional design scheme can not consider the distance, interference and power consumption at the same time.
SKU: CE-W016 -
IoT & Wireless
ESP 01 / ESP8266 Programmer CH340G Chip USB WiFi Wireless UART GPIO0
This moduel is an USB adpater / programmer for ESP8266 moduels of type ESP-01. It is conveniently fitted with a 2x4P 2.54mm female header to plug the ESP01 (according to illustration picture 2) and configure or run it right away. A large 1000μF cap will help getting a steady 5.0V VCC from the USb bus and and jumper (on the right of the 2x4P header) will help configuring the GPIO0 line according needs. The module is based on the USB-UART bridget CH340 from WCH which is compatible with all platforms.
SKU: CE-P003
There are no reviews yet.