ESP 01 / ESP8266 Programmer CH340G Chip USB WiFi Wireless UART GPIO0
3 in stock
This moduel is an USB adpater / programmer for ESP8266 moduels of type ESP-01. It is conveniently fitted with a 2x4P 2.54mm female header to plug the ESP01 (according to illustration picture 2) and configure or run it right away. A large 1000μF cap will help getting a steady 5.0V VCC from the USb bus and and jumper (on the right of the 2x4P header) will help configuring the GPIO0 line according needs. The module is based on the USB-UART bridget CH340 from WCH which is compatible with all platforms.
₹234.82 ₹497.96 Price Including GST
3 in stock
CompareESP 01 ESP8266 Programmer CH340G Chip USB WiFi Wireless
This moduel is an USB adpater /
programmer for ESP8266 moduels of type ESP-01.
It is conveniently fitted with a 2x4P
2.54mm female header to plug the ESP01
(according to illustration picture 2)
and configure or run it right away.
A large 1000μF cap will help getting a steady 5.0V VCC
from the USb bus and and jumper (on the right of the 2x4P header)
(we don’t offer any jumper !!!!)
will help configuring the GPIO0 line according needs.
The module is based on the USB-UART bridget CH340
from WCH which is compatible with all platforms.
Note : for an usage with Arduino ESP8266 platform and for Arduino IDE
it is necessary to switch manually the GPIO0 state for working mode,
in order to get a fully automatic upload it is most likely possible,
for a very limited effort, to assign an unused control line
from CH340 to driver the GPIO0 line
(probably at the cost of a necessary logic inversion),
refer to the CH340 datasheet and
most important to the NodeMCU V0.9
which use the CH340 and already implements this solution,
the schematic is open source and easily available.
For Tutorial Please Clink This:- Link
Based on 0 reviews
Be the first to review “ESP 01 / ESP8266 Programmer CH340G Chip USB WiFi Wireless UART GPIO0”
Related products
-
Circuits Boards & PCB, IoT & Wireless
ESP8266 12F Adapter Base Plate
This ESP8266 Adapter Plate is an Adapter PCB Plate for ESP-07, ESP-08, ESP-12E ESP8266 SMD ESP8266 Module. These SMD ESP8266 modules have an unfriendly pin pitch. But by use of this adapter PCB, you can solder ESP-07, ESP-08 or ESP-12E modules and can use your favorite ESP8266 SMD modules on breadboards or on perforated boards.
SKU: CE-W004-A -
IoT & Wireless, Modules & Sensors
NEO6MV2 GPS Module NEO-6M with Flight Control EEPROM
This is a complete GPS module that is based on the Ublox NEO-6M. This unit uses the latest technology from Ublox to give the best possible positioning information and includes a larger built-in 25 x 25mm active GPS antenna with a UART TTL socket. A battery is also included so that you can obtain a GPS lock faster. This is an updated GPS module that can be used with ardupilot mega v2. This GPS module gives the best possible position information, allowing for better performance with your Ardupilot or other Multirotor control platform.
The Ublox NEO-6M GPS engine on this board is a quite good one, with the high precision binary output. It has also high sensitivity for indoor applications. UBLOX NEO-6M GPS Module has a battery for power backup and EEPROM for storing configuration settings. The antenna is connected to the module through a ufl cable which allows for flexibility in mounting the GPS such that the antenna will always see the sky for best performance. This makes it powerful to use with cars and other mobile applications.
The Ublox GPS module has serial TTL output, it has four pins: TX, RX, VCC, and GND. You can download the u-center software for configuring the GPS and changing the settings and much more.
SKU: CE-M0110 -
Developments Boards, IoT & Wireless, Modules & Sensors
SN65HVD230 CAN Communication Module Bus Transceiver
Developments Boards, IoT & Wireless, Modules & SensorsSN65HVD230 CAN Communication Module Bus Transceiver
SN65HVD230 can be used under high interference environment. The device has the ability to send and receive good at different rates.Its main features are as follows: Fully compatible with ISO11898 standard; High input impedance. allowing 120 nodes; Low current standby mode. the typical current of 370A; Signal transfer rate up to 1Mb / s;Thermal protection. open circuit failure protection function; With anti-instantaneous interference protection bus; Slope control. reduce radio frequency interference (RFI);Differential receiver with a wide range of anti-common-mode interference. electromagnetic interference (EMI) capabilities.
SKU: CE-M065 -
Circuits Boards & PCB, IoT & Wireless, Power Supply
Battery Shield For WeMos D1 mini battery Charging and Boost
Circuits Boards & PCB, IoT & Wireless, Power SupplyBattery Shield For WeMos D1 mini battery Charging and Boost
The WeMos lithium battery shield provides a means of powering your WeMos mini, or WeMos mini Pro (see item HCWEMO0002) from a single cell (3.7V) lithium battery. The shield contains a DC-DC converter to step-up the batteries 3.7V to 5V supplying your WeMos mini and shields with up to 1A of power. When the battery is depleted simply plug the shield into a USB power source using a mini USB cable and it will automatically recharge the battery. Two LEDs on the shield indicate when the battery is charging and when charging has completed.
SKU: CE-M086
There are no reviews yet.