-
×
DC Jack 5.5 X 2.1mm male With 9 inch Wire
1 × ₹11.80 -
×
AC Socket C8 Panel Mount 250AC 2.5A
1 × ₹11.80
Subtotal: ₹23.60 (incl. tax)
Shop
Showing 196–210 of 608 results
-
Motor Drives & controllers, Robots & Kits
Dual Shaft BO Motor-Straight 300 RPM
Dual shaft DC motor with gear box which gives good torque and rpm at lower voltages. This motor can run at approximately 200rpm when driven by a Dual Li-Ion cell battery at 6 V and approximately at 300 rpm when driven by a 9V Li-Ion cell.It is most suitable for light weight robot running on small voltage. Out of its two shafts one shaft can be connected to wheel, other can be connected to the position encoder.
SKU: CE-M0134 -
Modules & Sensors
Dust Smoke Particle Sensor GP2Y1010AU0F
GP2Y1010AU0F Module is used to Sense Dust Particles in air and also called as an optical air quality sensor. It is very much smaller in size. It detects the reflected light of dust in the air. Especially, it is effective to detect very fine particle like cigarette smoke. In addition, it can distinguish smoke from house dust by pulse pattern of output voltage and is commonly used in air purifier systems. The sensor has a very low current consumption (20mA max, 11mA typical), and can be powered with up to 7VDC. The output of the sensor is an analog voltage proportional to the measured dust density, with a sensitivity of 0.5V/0.1mg/m3.
SKU: CE-M0165 -
-
IoT & Wireless
esp-01 Breadboard Adapter Breakout Board
As the ESP8266 ESP-01 module can not be plugged directly into the breadboard, this is a breadboard adapter for the popular ESP-01 model of the ESP8266 serial WiFi transceiver module. It is specially designed for breadboard and PCB experiment board project.It leads out all pins of the ESP-01 module directly, and marked the pin names. An electrolytic capacitor has been added to filter the power supply.
SKU: CE-M0120 -
IoT & Wireless, Modules & Sensors
ESP32 Development Board WiFi+Bluetooth 30 pin
ESP32 Development board is based on the ESP WROOM32 WIFI + BLE Module.It’s a low-footprint, minimal system development board powered by the latest ESP-WROOM-32 module and can be easily inserted into a solderless breadboard.
It contains the entire basic support circuitry for the ESP-WROOM-32, including the USB-UART bridge, reset- and boot-mode buttons, LDO regulator and a micro-USB connector. Every important GPIO is available to the developer.
SKU: CE-M0153 -
IoT & Wireless, Modules & Sensors
ESP32 Development Board WiFi+Bluetooth 38 Pin
ESP32 Development board is based on the ESP WROOM32 WIFI + BLE Module.It’s a low-footprint, minimal system development board powered by the latest ESP-WROOM-32 module and can be easily inserted into a solderless breadboard.
It contains the entire basic support circuitry for the ESP-WROOM-32, including the USB-UART bridge, reset- and boot-mode buttons, LDO regulator and a micro-USB connector. Every important GPIO is available to the developer.
SKU: CE-M0152 -
IoT & Wireless
ESP32S Wroom Wireless Wifi Bluetooth Module Adapter Plate
The ESP32 is a very powerful Wifi and Bluetooth module but difficult to work with due to its small size and many available pins. The pins are extremely close to each other and nearly impossible to solder wires to it.
SKU: CE-W012-1 -
Toys , RC Plane & Drone
F450 Quadcopter Frame Kit with Integrated PCB
It is 450mm quad frame built from quality materials. The main frame is glass fiber while the arms are constructed from ultra durable polyamide nylon. This version of the F450 features integrated PCB connections for direct soldering of your ESCs.This eliminates the need for a power distribution board or messy multi-connectors keeping your electronics layout very tidy. F450 also comes with stronger molded arms, so no more arm breakage at the motor mount on a hard landing.
Assembly is a breeze with pre-threaded brass sleeves for all of the frame bolts, so no lock-nuts are required. It utilizes one size of bolt for the entire build, making the hardware very easy to keep in order and only requiring one size of hex wrench to assemble.SKU: CE-T056
