Out of stock
The sensitive type photosensitive resistance sensor. Using LDR as a main sensor.With adjustable potentiometer adjustable testing light brightness
₹92.04 Price Including GST
Out of stock
Digital Light Sensor Light Detection Module 4Pin
Product Description:-
1, Using sensitive photosensitive resistance sensor
2,The comparator output signal is clean, good waveform, driving ability, more than 15mA.
3, With adjustable potentiometer to adjust the brightness of the light detection
4,The working voltage 3.3V-5V
5 DUAL OUTPUT form: DO digital switching outputs (0 and 1) and AO analog voltage output
6 A fixed bolt holes for easy installation
7 PCB Size: 3.2cm x 1.4cm
8 Using a wide voltage LM393 comparator
Product wiring instructions:
1 VCC positive power supply 3.3-5V
2 GND power supply is negative
3 DO TTL switching signal output
4 AO analog output
HR202 is a new kind of humidity-sensitive resistor made from organic macromolecule materials, it can be used in occasions like: hospitals, storage, workshop, textile industry, tobaccos, pharmaceutical field, meteorology, etc.
This tiny Flame sensor infrared receiver module ignition source detection module is Arduino compatible can use to detect flame or wavelength of the light source within 760nm~1100nm also useful for Lighter flame detect at the distance 80cm. Greater the flame, farther the test distance.It has the Detect angle of 60 degrees and very sensitive to flame spectrum. It produces the one channel output signal at D0 terminal for further processing like an alarm system or any switching system. The sensitivity is adjustable with the help of blue potentiometer given on the board.
This product is a serially driven 8×8 LED Matrix which powered by MAX7219.The 8×8 LED Matrix is easy to use and compatible with Arduino, only needs three data lines and two power lines. It can be used in lots of place like various types of electronic display panels. You can make your applications more vivid because of the LED brightness adjustment can be implemented in software. For the kit of this module
TTP226 8-Way Capacitive Touch Sensor / Switch Module is based on a touch-sensing IC enabling capacitive touch switch mode. In the normal state, the module output is low, low power consumption. When a finger touches the corresponding position, the module output high, if not touched for 12 seconds, switch to low-power mode.
This is a 2 Channel 5V Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Microcontroller(Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) .
ADXL345 Tripple Axis Accelerometer Board is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16g. Digital output data is format as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface. calcuttaelectronics.com
The ADXL345 Tripple Axis Accelerometer Board is well suited for mobile device applications. It measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Its high resolution (4 mg/LSB) enables measurement of inclination changes less than 1.0°.
Several special sensing functions are provided. Activity and inactivity sensing detect the presence or lack of motion and if the acceleration on any axis exceeds a user-set level. Tap sensing detects single and double taps. Free-fall sensing detects if the device is falling. These functions can be mapped to one of two interrupt output pins. An integrated, patent pending 32-level first in, first out (FIFO) buffer can be used to store data to minimize host processor intervention.
Low power modes enable intelligent motion-based power management with threshold sensing and active acceleration measurement at extremely low power dissipation.
Select at least 2 products
to compare
XT60 Bullet Connectors Male Female Pair 
ESP 01 / ESP8266 Programmer CH340G Chip USB WiFi Wireless UART GPIO0 
There are no reviews yet.