Out of stock
The sensitive type photosensitive resistance sensor. Using LDR as a main sensor.With adjustable potentiometer adjustable testing light brightness
₹92.04 Price Including GST
Out of stock
Digital Light Sensor Light Detection Module 4Pin
Product Description:-
1, Using sensitive photosensitive resistance sensor
2,The comparator output signal is clean, good waveform, driving ability, more than 15mA.
3, With adjustable potentiometer to adjust the brightness of the light detection
4,The working voltage 3.3V-5V
5 DUAL OUTPUT form: DO digital switching outputs (0 and 1) and AO analog voltage output
6 A fixed bolt holes for easy installation
7 PCB Size: 3.2cm x 1.4cm
8 Using a wide voltage LM393 comparator
Product wiring instructions:
1 VCC positive power supply 3.3-5V
2 GND power supply is negative
3 DO TTL switching signal output
4 AO analog output
This tiny Flame sensor infrared receiver module ignition source detection module is Arduino compatible can use to detect flame or wavelength of the light source within 760nm~1100nm also useful for Lighter flame detect at the distance 80cm. Greater the flame, farther the test distance.It has the Detect angle of 60 degrees and very sensitive to flame spectrum. It produces the one channel output signal at D0 terminal for further processing like an alarm system or any switching system. The sensitivity is adjustable with the help of blue potentiometer given on the board.
HR202 is a new kind of humidity-sensitive resistor made from organic macromolecule materials, it can be used in occasions like: hospitals, storage, workshop, textile industry, tobaccos, pharmaceutical field, meteorology, etc.
USBasp is a USB in-circuit programmer for Atmel AVR controllers. It simply consists of an ATMega8 and a couple of passive components. The programmer uses a firmware-only USB driver, no special USB controller is needed, and thats make it low cost USB programmer.
The Programmer works on USB port and can be used with Laptops. Software is compatible with Windows Vista and Windows 7. High speed programming and does’t require external power.
This is a dual axis high quality JoyStick Module . It can be used to sense movements in 2 directions(axes). It also has a inbuilt switch which can be activated by pressing the stick.Directional movements are simply two potentiometers – one for each axis. Pots are ~10k each.
With the help of this Joystick Module, you can measure position coordinates on the X and Y axis by moving the “hat”. It also contains a switch that is press-able by pushing the “hat”.It also contains a switch that is press-able by pushing the “hat” down. Similar to the XBOX controller.The X and Y axes are two 10k potentiometers which control 2D movement by generating analog signals. When the module is in working mode, it will output two analog values, representing two directions. This module uses the 5V power supply, and value, when reading through analog input, would be about 2.5V, a value will increase with joystick movement and will go up till maximum 5V; the value will decrease when the joystick is moved in other direction till 0V.
NRF24L01+ Module This module based on Nordic nRF24L01+, highly integrated, ultra-low power (ULP) 2Mbps RF transceiver for the 2.4GHz ISM (Industrial, Scientific and Medical) band. Nordic nRF24L01+ integrates a complete 2.4GHz RF transceiver, RF synthesizer, and baseband logic including the Enhanced ShockBurst™ hardware protocol accelerator supporting a high-speed SPI interface for the application controller.
SN65HVD230 can be used under high interference environment. The device has the ability to send and receive good at different rates.Its main features are as follows: Fully compatible with ISO11898 standard; High input impedance. allowing 120 nodes; Low current standby mode. the typical current of 370A; Signal transfer rate up to 1Mb / s;Thermal protection. open circuit failure protection function; With anti-instantaneous interference protection bus; Slope control. reduce radio frequency interference (RFI);Differential receiver with a wide range of anti-common-mode interference. electromagnetic interference (EMI) capabilities.
Select at least 2 products
to compare
RA-02 LoRa Module Breakout Board, RF Wireless Transceiver 
HC SR501 INFRARED IR PIR MOTION SENSOR for Arduino AVR 
OV7670 640X480 VGA CMOS CAMERA SENSOR 
There are no reviews yet.