Developments Boards
Showing 46–60 of 66 results
-
Developments Boards, Modules & Sensors
MQ-5 LPG Liquid Propane Methane Gas Sensor Module
Gas Sensor(MQ5) module is useful for gas leakage detection (in home and industry). It is suitable for detecting H2, LPG, CH4, CO, Alcohol. Due to its high sensitivity and fast response time, measurements can be taken as soon as possible. The sensitivity of the sensor can be adjusted by using the potentiometer
SKU: CE-M093 -
Developments Boards, Modules & Sensors
MQ7 – Carbon Monoxide Gas Sensor Module
This Carbon Monoxide (CO) gas sensor detects the concentrations of CO in the air and ouputs its reading as an analog voltage. The sensor can measure concentrations of 10 to 10,000 ppm.The sensor can operate at temperatures from -10 to 50°C and consumes less than 150 mA at 5V.
SKU: CE-M078 -
Developments Boards, Display Module
Nokia 5110 LCD Module Blue Back light Adapter for Arduino
Nokia 5110 LCD Display Module is a low-cost monochrome LCD module comprised of 84 X 48 pixels that can be used to display rich graphic and text content. Though it’s an industrial module, this LCD display is extremely easy to use. This module is a revision that accepts 3-5V input. So no extra level shifter is needed. To have full control, you just need 5 pins. And as a classic display module among open source communities,
SKU: CE-M038-1 -
Developments Boards, Display Module
Nokia 5110 LCD Module White Back light Adapter for Arduino
Nokia 5110 LCD Display Module is a low-cost monochrome LCD module comprised of 84 X 48 pixels that can be used to display rich graphic and text content. Though it’s an industrial module, this LCD display is extremely easy to use. This module is a revision that accepts 3-5V input. So no extra level shifter is needed. To have full control, you just need 5 pins. And as a classic display module among open source communities,
SKU: CE-M038 -
Developments Boards, IoT & Wireless, Modules & Sensors
NRF24L01+ 2.4GHz Antenna Wireless Transceiver Module
Developments Boards, IoT & Wireless, Modules & SensorsNRF24L01+ 2.4GHz Antenna Wireless Transceiver Module
NRF24L01+ Module This module based on Nordic nRF24L01+, highly integrated, ultra-low power (ULP) 2Mbps RF transceiver for the 2.4GHz ISM (Industrial, Scientific and Medical) band. Nordic nRF24L01+ integrates a complete 2.4GHz RF transceiver, RF synthesizer, and baseband logic including the Enhanced ShockBurst™ hardware protocol accelerator supporting a high-speed SPI interface for the application controller.
SKU: CE-W001 -
Developments Boards, Modules & Sensors, Robots & Kits
OV7670 640X480 VGA CMOS CAMERA SENSOR
OV7670 image sensor, small size, low operating voltage, and provides all the features of the single-chip VGA camera and image processor. Through theSCCB bus control, you can output the entire frame, sub-sampled, take the window way affect the data resolution of 8 bits. VGA image of the product is up to 30 frames / sec. Users can fully control the image quality, data format and transmission mode. The process of image processing functions including gamma curves, white balance, saturation, chroma, and so can beprogrammed through the SCCB interface. OmmiVision image sensor applications unique sensor technology to improve image quality by reducing or eliminating the optical or electronic defect, such as fixed pattern noise, tail-blooming, clear and stable color image.
SKU: CE-M085 -
Developments Boards, Modules & Sensors
RFID RC522 Reader & Writer CARD AND KEYCHAIN
Mifare RC522 is the high integrated RFID card reader which works on non-contact 13.56mhz communication, is designed by NXP as a low power consumption, low cost and compact size read and write chip, is the best choice in the development of smart meters and portable hand-held devices.
SKU: CE-M079 -
Developments Boards, Modules & Sensors
Rotary Encoder Module Brick Sensor arduino KY-040
The Keyes KY-040 rotary encoder is a rotary input device (as in knob) that provides an indication of how much the knob has been rotated AND what direction it is rotating in.It’s a great device for stepper and servo motor control. You could also use it to control devices like digital potentiometers..
SKU: CE-M049 -
Developments Boards, IoT & Wireless, Modules & Sensors
SN65HVD230 CAN Communication Module Bus Transceiver
Developments Boards, IoT & Wireless, Modules & SensorsSN65HVD230 CAN Communication Module Bus Transceiver
SN65HVD230 can be used under high interference environment. The device has the ability to send and receive good at different rates.Its main features are as follows: Fully compatible with ISO11898 standard; High input impedance. allowing 120 nodes; Low current standby mode. the typical current of 370A; Signal transfer rate up to 1Mb / s;Thermal protection. open circuit failure protection function; With anti-instantaneous interference protection bus; Slope control. reduce radio frequency interference (RFI);Differential receiver with a wide range of anti-common-mode interference. electromagnetic interference (EMI) capabilities.
SKU: CE-M065 -
-
Developments Boards
ST-Link V2 Mini STM8 STM32 Simulator Download Programmer
The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families. The single wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board.
- internal motherboard, U disk shell using aluminum alloy installation, convenient to carry, safe and reliable!
- interface definition on the shell directly tagging, be clear at a glance, convenient and practical!
- 5 V, 3.3 V available at the same time, convenient for you to link the 5 V and 3.3 V target board
- shell characters using laser laser, laser engraving, never fade off! Permanent clear!
- internal motherboard with 500 ma self recovery fuse, completely protect your expensive computer motherboard!
- The LED indicator light, convenient you always observes the working state of the ST cc-link V2!
- Distribution 4 with dupont line, let you can easily cope with different target plate line order!
- Use anti-static bag packaging, automatic sealing machine sealed packaging, safe and reliable, does not fear the electrostatic, not afraid of water!
SKU: CE-P001 -
Developments Boards
STM32F103C8T6-ARM-STM32-Minimum-System-Development-Board
This is STM32F103C8T6 Minimum System Board Microcomputer STM32 ARM Core Board. This board is low cost Minimum System Development Board for ARM Microcontroller STM32F103C8T6. Board is suitable for learners that want to learn STM32 microcontroller with ARM Coretex-M3 32-bit core.
SKU: CE-D002 -
Developments Boards
STM8S103F3P6 STM8 Minimum System Development Board
STM8S core board of the highlights: The development board using MicroUSB cable supply, compatible with smart phone lines, data lines is simple and easy to get, but not USB MINI line-powered, USB MINI line is not easy to find, has been gradually phased out. Other manufacturers of products are used in MINI-USB port, this is not applicable for customers. Low price, user-friendly design, a full set of data, allowing you to save money, save time, effort, worry!
SKU: CE-D004 -
Developments Boards, Modules & Sensors
TTP223 CAPACITIVE TOUCH MODULE
The module is based on a touch-sensing IC (TTP223B) capacitive touch switch module. In the normal state, the module output low, low power consumption. When a finger touches the corresponding position, the module output high, if not touched for 12 seconds, switch to low-power mode. Job type: the initial state is low, high touch, do not touch is low ( similar touch of a button feature ). A module can be installed in such as surface plastic, the glass of non-metallic materials
In addition to the thin paper ( non-metallic ) covering the surface of the module, as long as the correct location of the touch, you can make hidden in the walls, desktops and other parts of buttons.
SKU: CE-M0106