Showing 541–555 of 608 results
Several Values Of Registers.You can Buy as per your requirement. Metal film resistors have a thin metal layer as resistive element on a non-conducting body. They are among the most common types of axial resistors. Other film type resistors are carbon film and thick and thin film resistors. In most literature referrals to metal film, usually it is a cylindrical axial resistor. However, thin film chip resistors use the same manufacturing principle for the metal layer. The appearance of metal film resistors is similar to carbon film resistors, but their properties for stability, accuracy and reliability are considerably better.
TowerPro MG995 Metal Gear Servo Motor is a high-speed standard servo can rotate approximately 120 degrees (60 in each direction). You can use any servo code, hardware or library to control these servos, so it’s great for beginners who want to make stuff move without building a motor controller with feedback & gear box, especially since it will fit in small places. The MG995 Metal Gear Servo also comes with a selection of arms and hardware to get you set up nice and fast.This is the most famous servo made by TowerPro . MG995 is a digital metal gear high torque servo for airplane, helicopter, RC-cars and many RC model
These 2-wire cables are 16cm long and come as a set. One side has a 2-pin JST SM type connector plug on the end. The other side has a matching 2-pin JST SM type receptacle connector. They are good for whenever you have 2 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from coming apart easily.
The module (MicroSD Card Adapter) is a Micro SD card reader module, through the file system and the SPI interface driver, MCU to complete the file system to read and write MicroSD card. Users can directly use IDE comes with an SD card to complete the library card initialization and read-write
USB On-The-Go, often abbreviated to USB OTG or just OTG, is a specification first used in late 2001 that allows USB devices, such as tablets or smartphones, to act as a host, allowing other USB devices, such as USB flash drives, digital cameras, mice or keyboards, to be attached to them.
Supports sampling rates (KHz): 8 / 11.025 / 12/16 / 22.05 / 24/32 / 44.1 / 48. 24-bit DAC output, support dynamic range: 90dB, SNR support: 85dB. Fully supports FAT16, FAT32 file system, maximum support 32G TF card, support U disk to 32G, 64M bytes NORFLASH. A variety of control modes are available. IO control, serial port, AD button control mode. Radio spots language function, you can pause the background music being played. Advertising finished playing background sound continues to play back
FM radio,· USB MP3 PLAY,· SD MP3 PLAY,· Remote operated, Led display, 5v operated.This type of ready-made MP3-FM kits With Bluetooth support.low cost .The kit consists of one main board, one connector wire, one USB socket+wire, one remote with battery.
GY-521 MPU6050 Module 3 Axis analog gyro sensors+ 3 Axis Accelerometer Module, MPU-6050 3 Axis Gyroscope Module For Arduino A 3-axis gyroscope and a 3-axis accelerometer are combined together on the same silicon die with an onboard Digital Motion Processor.MPU6050 Module 3 Axis analog gyro sensors+ 3 Axis Accelerometer Module Easy to get it fit into your project!
Gas Sensor(MQ5) module is useful for gas leakage detection (in home and industry). It is suitable for detecting H2, LPG, CH4, CO, Alcohol. Due to its high sensitivity and fast response time, measurements can be taken as soon as possible. The sensitivity of the sensor can be adjusted by using the potentiometer
This Carbon Monoxide (CO) gas sensor detects the concentrations of CO in the air and ouputs its reading as an analog voltage. The sensor can measure concentrations of 10 to 10,000 ppm.The sensor can operate at temperatures from -10 to 50°C and consumes less than 150 mA at 5V.
MT3608 2A Max DC-DC Step Up Power Module Booster
Specifications:
2V to 24V input voltage with output boost 5V to 28V adjustable
Maximum output current: 2A
Input voltage: 2V ~ 24V
Maximum output voltage: > 5V – 28V
Efficiency: > 93%
Input voltage should not exceed the maximum input voltage
Peak current output current should not more than 2A
Output voltage should always be higher than Input voltage
PCB Size: 36 mm * 17 mm * 14 mm
This is a complete GPS module that is based on the Ublox NEO-6M. This unit uses the latest technology from Ublox to give the best possible positioning information and includes a larger built-in 25 x 25mm active GPS antenna with a UART TTL socket. A battery is also included so that you can obtain a GPS lock faster. This is an updated GPS module that can be used with ardupilot mega v2. This GPS module gives the best possible position information, allowing for better performance with your Ardupilot or other Multirotor control platform.
The Ublox NEO-6M GPS engine on this board is a quite good one, with the high precision binary output. It has also high sensitivity for indoor applications. UBLOX NEO-6M GPS Module has a battery for power backup and EEPROM for storing configuration settings. The antenna is connected to the module through a ufl cable which allows for flexibility in mounting the GPS such that the antenna will always see the sky for best performance. This makes it powerful to use with cars and other mobile applications.
The Ublox GPS module has serial TTL output, it has four pins: TX, RX, VCC, and GND. You can download the u-center software for configuring the GPS and changing the settings and much more.
4v battery charger SLA & LED driver From 220V AC 
