Shop
Showing 526–540 of 612 results
-
Circuits Boards & PCB, Developments Boards, Modules & Sensors
Joystick Module Dual Axis XY for arduino & other
Circuits Boards & PCB, Developments Boards, Modules & SensorsJoystick Module Dual Axis XY for arduino & other
This is a dual axis high quality JoyStick Module . It can be used to sense movements in 2 directions(axes). It also has a inbuilt switch which can be activated by pressing the stick.Directional movements are simply two potentiometers – one for each axis. Pots are ~10k each.
With the help of this Joystick Module, you can measure position coordinates on the X and Y axis by moving the “hat”. It also contains a switch that is press-able by pushing the “hat”.It also contains a switch that is press-able by pushing the “hat” down. Similar to the XBOX controller.The X and Y axes are two 10k potentiometers which control 2D movement by generating analog signals. When the module is in working mode, it will output two analog values, representing two directions. This module uses the 5V power supply, and value, when reading through analog input, would be about 2.5V, a value will increase with joystick movement and will go up till maximum 5V; the value will decrease when the joystick is moved in other direction till 0V.
SKU: CE-M096 -
Motor Drives & controllers
L298N DC Motor Driver Controller 2A Stepper Motor Board Module
The L298N driver module, using ST’s L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface can 5V single-chip circuitry to supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential. Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability, low calorific value and strong anti-interference ability.
SKU: CE-M084 -
-
Batteries & Chargers, Circuits Boards & PCB
Lipo Battery Low Voltage Tester 1S-8S Buzzer
The LiPo low voltage Tester cum Alarm is small and light for on board use, plugs into balance lead for detecting low voltage on individual cells. A loud alarm will go off with flashing LED if the voltage on any of the individual cells drops below the adjustable threshold. Essential while working with any Lithium Polymer battery.
SKU: CE-M071 -
Batteries & Chargers, Battery holder & Box, Circuits Boards & PCB, Power Supply
Lithium Battery Charging Board TP 4056 Micro USB with Protection
Batteries & Chargers, Battery holder & Box, Circuits Boards & PCB, Power SupplyLithium Battery Charging Board TP 4056 Micro USB with Protection
This tiny module is perfect for charging single cell 3.7V 1 Ah or higher LiPo cells such as 16550s that don’t have their own protection circuit.Based around the TP4056 charger IC and DW01 battery protection IC this module will offer 1A charge current then cut off when finished.Futhermore when the battery voltage drops below 2.4V the protection IC will switch the load off to protect the cell from running at too low of a voltage – and also protects against over-voltage and reverse polarity connection (it will usually destroy itself instead of the battery) however please check you have it connected correctly the first time.
For Bulk Quantity Please call US:- +91 9830150448
SKU: CE-M029 -
SMD
LL34 SMD Zener diode package 1/2W Multiple Value
SMD diodes LL34 have a range of anode/cathodeidentifiers. Sometimes it’s easiest to just use a multimeter to test for polarity. Turn the multimeter to the diode setting (usually indicated by a diodesymbol), and touch each probe to one of the LEDterminals. … Diodes certainly aren’t the only polarized component.
SKU: CE-C002 -
Batteries & Chargers, Circuits Boards & PCB, Power Supply
LM 2596 DC Buck Converter Module
This is an LM2596 DC-DC buck converter step-down power module with high-precision potentiometer for adjusting output voltage, capable of driving a load up to 3A with high efficiency. When the output current required is greater than 2.5A(10W) an external heatsink is suggested. Use on board switch to change display measurement between the input or output voltage, and a LED indicate which value(IN/OUT) is being measured. This setting is stored even after power off. Voltmeter can be turned off, just keep the switch pressed for 1 second and leave it. Adjust Input and output voltage measurement error offset – long press switch for 4 seconds or more, the digital display flashes, then short press the button to change the value of output (values range from -0.5 to 0.5, the unit is V), a positive number indicates an upward calibration, negative downward calibration. Now press the button again for adjust input offset in same manner.
SKU: CE-M064 -
Components, SMD
LM393 SOP8 Low Power Low Offset Voltage Dual Comparator
LM393 SOP8 Low Power Low Offset Voltage Dual Comparator.The LM393 is a dual differential comparator; this means that it accepts 2 inputs for comparison. It compares these voltage inputs and determines which is the larger value. Based on this, electronic decisions can be made based on which input is greater and which is smaller.
SKU: CE-S-LM393 -
Tools & DIY
Macro Extension Tube 65mm Viltrox DG – C Metal and Plactic 12MM 20MM 36MM AF Auto Focus
This extension tube set can help you achieve macro lens while not affect the picture quality because there is no optics inside. The closer the focus, the greater the magnification.
It is used between camera body and 35mm single-lens reflex camera. It comes as a set of 3 tubes in different lengths, and you can use them in single ones or in combinations as prefer. The electronic copper pins make it perfect to couple with camera’s auto diaphragm, TTL metering.
Fit for Canon EOS series camera and DSLR cameraSKU: CE-T015 -
Developments Boards, Display Module
MAX 7219 8X8 dot matrix module LED For Arduino & other
This product is a serially driven 8×8 LED Matrix which powered by MAX7219.The 8×8 LED Matrix is easy to use and compatible with Arduino, only needs three data lines and two power lines. It can be used in lots of place like various types of electronic display panels. You can make your applications more vivid because of the LED brightness adjustment can be implemented in software. For the kit of this module
SKU: CE-M015 -
Developments Boards, Modules & Sensors
MAX30100 Heart Rate sensor modules
Heart Rate click carries Maxim’s MAX30100 integrated pulse oximetry and heart-rate sensor. It’s an optical sensor that derives its readings from emitting two wavelengths of light from two LEDs – a red and an infrared one – then measuring the absorbance of pulsing blood through a photodetector. This particular LED color combination is optimized for reading the data through the tip of one’s finger. The signal is processed by a low-noise analog signal processing unit and communicated to the target MCU through the mikroBUS I2C interface. Developers of end-user applications should note that the readings can be negatively impacted by excess motion and changes in temperature. Also, too much
pressure can constrict capillary blood flow and therefore diminish the reliability of the data. A programmable INT pin is also available. Uses3.3V power supply.SKU: CE-M0103